- 相關推薦
思科路由器設置VPDN的方法
CCNA 重新認證：CCNA認證證書的時效性是三年。要重新更新證書，必須通過CCNA的考試(如果通過的下一階段CCNP的考試，CCNA認證證書會被自動更新)下面是小編整理的關于思科路由器設置VPDN的方法，歡迎大家參考!
1 啟用aaa new-model
aaa new-model
2、建立認證方式
aaa authentication ppp mytest local (這里為本地認證)
3、啟用VPDN
vpdn enable
4、建立VPDN組
vpdn-group mytest
! Default L2TP VPDN group
accept-dialin
protocol l2tp
virtual-template 1
local name mytest-name
lcp renegotiation always //注意非常重要，否則LCP不會自協商，那么路由器的MTU值一定要和對方LAC發過來的要匹配，否則LCP失敗
l2tp tunnel password 7 00090A1201481F
source-ip x.x.x.x
5、建立IP 本地POOL
ip local pool mytest-01 172.23.1.2 172.23.1.254
6、配置虛模板
interface Virtual-Template1
ip address 172.23.1.1 255.255.255.0
peer default ip address pool mytest-01
ppp authentication pap mytest
5200g
domain qh.org
authentication-scheme vpdn_none
accounting-scheme vpdn_none
l2tp-group qh.org
l2tp-group qh.org
tunnel password simple mytest
tunnel name mytest
start l2tp ip x.x.x.x
tunnel source LoopBack0
附：L2TP協議結構
1、IP包頭 20字節
2、UDP報頭 8字節
3、L2TP報頭 12字節：包括：
1)the version and flag fields (2 bytes)
2)the tunnel id and session id fields (2 bytes each)
3)2 bytes of padding offset
4)4 bytes of Point-to-Point Protocol (PPP) encapsulation
//以下是沒有啟用LCP自協商的DEBUG 連接失敗
Jul 25 00:03:48.084: Vi1 VPDN: Virtual interface created for qh@qh.org
Jul 25 00:03:48.084: Vi1 PPP: Phase is DOWN, Setup
Jul 25 00:03:48.084: Vi1 VPDN: Clone from Vtemplate 1 filterPPP=0 blocking
Jul 25 00:03:48.204: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up
Jul 25 00:03:48.204: Vi1 PPP: Using set call direction
Jul 25 00:03:48.204: Vi1 PPP: Treating connection as a callin
Jul 25 00:03:48.204: Vi1 PPP: Phase is ESTABLISHING, Passive Open
Jul 25 00:03:48.204: Vi1 LCP: State is Listen
Jul 25 00:03:48.204: Vi1 VPDN: Bind interface direction=2
Jul 25 00:03:48.204: Vi1 LCP: I FORCED CONFREQ len 14
Jul 25 00:03:48.204: Vi1 LCP: MRU 1492 (0x010405D4)
Jul 25 00:03:48.204: Vi1 LCP: AuthProto PAP (0x0304C023)
Jul 25 00:03:48.204: Vi1 LCP: MagicNumber 0x01022143 (0x050601022143)
Jul 25 00:03:48.204: Vi1 VPDN: PPP LCP accepted rcv CONFACK
Jul 25 00:03:48.204: Vi1 LCP: I FORCED CONFACK len 10
Jul 25 00:03:48.204: Vi1 LCP: MRU 1480 (0x010405C8)
Jul 25 00:03:48.204: Vi1 LCP: MagicNumber 0x082D5DCE (0x0506082D5DCE)
Jul 25 00:03:48.204: Vi1 VPDN: PPP LCP not accepting sent CONFACK
Jul 25 00:03:48.204: Vi1 VPDN: Unbind interface
Jul 25 00:03:48.296: Vi1 PPP: No remote authentication for call-in
Jul 25 00:03:48.560: Vi1 PPP: Missed link down notification
Jul 25 00:03:48.560: Vi1 LCP: State is Closed
【思科路由器設置VPDN的方法】相關文章：
kingnet路由器的設置方法01-18
思科路由器廣域網協議設置06-30
思科路由器密碼恢復方法10-24
圖解dlink路由器的設置方法10-10
詳細介紹totolin路由器的設置方法10-19
思科認證科目設置08-19
思科路由器的安全配置06-03
思科路由器配置基礎08-13