- 相關推薦
cisco路由器ppp認證方式
一、實驗拓撲
二、實驗要求：
1、要求配置ppp協議
2、分別用pap、chap認證
3、配置總部的路由器給分部的路由器分配ip地址，并且從地址池中分配，
4、pc1最終能ping銅pc2
三、實驗步驟：
1、配置各路由器接口的ip地址 如圖---
2、封裝ppp協議
R1(config)#interface s1/0
R1(config-if)#encapsulation ppp
R1(config-if)#clock rate 64000
R1(config-if)#ip address 192.168.2.1 255.255.255.0
R1(config-if)#no shut
R2(config)#interface s1/0
R2(config-if)#encapsulation ppp
R2(config-if)#no shut
R2(config-if)#clock rate 64000 配置DCE端時鐘頻率
3、配置IP地址池協商，并從地址池中獲取
R1(config)#interface s1/0
R1(config-if)#peer default ip address pool aaa
R1(config-if)#ip local pool aaa 192.168.2.2 192.168.2.10
R2(config)#interface s1/0
R2(config-if)#ip address negotiated
查看 s1/0接口的地址
R2#show interface s1/0
Serial1/0 is up, line protocol is up
Hardware is M4T
Internet address is 192.168.2.2/32 如果獲取不到地址將接 shutdown 然后再 no shudown
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, LCP Open
Open: CDPCP, IPCP, crc 16, loopback not set
Keepalive set (10 sec)
4、啟用rip協議 并查看路由表
R1(config)#router rip
R1(config-router)#network 192.168.2.0
R1(config-router)#network 192.168.1.0
查看路由表
R1#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter ar
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-I
ia - IS-IS inter area, * - candidate default, U - per-user s
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
C 192.168.1.0/24 is directly connected, FastEthernet0/0
192.168.2.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.2.2/32 is directly connected, Serial1/0
C 192.168.2.0/24 is directly connected, Serial1/0
R 192.168.3.0/24 [120/1] via 192.168.2.2, 00:00:47, Serial1/0
R2(config)#router rip
R2(config-router)#network 192.168.2.0
R2(config-router)#network 192.168.3.0
R2(config-router)#exit
查看路由表
R2#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BG
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF in
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA externa
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2
ia - IS-IS inter area, * - candidate default, U - per-
o - ODR, P - periodic downloaded static route
Gateway of last resort is not set
192.168.2.0/32 is subnetted, 2 subnets
C 192.168.2.2 is directly connected, Serial1/0
C 192.168.2.1 is directly connected, Serial1/0
C 192.168.3.0/24 is directly connected, FastEthernet0/0
5、配置PAP認證
R1(config)#username abc password 0 123
R1(config)#interface s1/0
R1(config-if)#ppp authentication pap
R2(config)#interface s1/0
R2(config-if)#ppp pap sent
R2(config-if)#ppp pap sent-username abc password 0 123
查看show run
interface Serial1/0
ip address negotiated
encapsulation ppp
serial restart-delay 0
clockrate 64000
ppp pap sent-username abc password 0 123
6、配置chap認證
R1(config)#username abc password 0 123 以對方的主機名作為用戶名，密碼要和對方的路由器一致
R1(config)#interface s1/0
R1(config-if)#ppp authentication pap
R1(config-if)#exit
R1(config)#username R2 password 0 123
R1(config)#interface s1/0
R1(config-if)#encapsulation ppp
R1(config-if)#ppp authentication chap chap 認證
R2(config)#username R1 password 0 123
R2(config)#interface s1/0
R2(config-if)#encapsulation ppp
R2#debug ppp authentication
PPP authentication debugging is on 驗證chap過程
【cisco路由器ppp認證方式】相關文章：
CISCO路由器CHAP認證配置06-17
Cisco認證的就業方向08-06
2016年思科認證輔導：cisco路由器忘記密碼恢復08-23
Cisco路由器配置命令大全06-12
Cisco路由器安全配置命令10-27
cisco路由器voip配置解析201610-16
Cisco路由器如何配置實現VoIP04-28
CISCO路由器配置命令詳解設置試題08-28
Cisco路由器配置入門知識大全08-02